又來SPL1000ULTRA問題幾個 (Velodyne SPL1000 Ultra subwoofer)

Foverking

新入了1000ULTRA, 用緊條舊SUB-X比佢, 電源線用緊跟機的, RUN了2+幾個鐘, 覺得力度差D, D聲都係唔夠緊/快, Ching門, 比d意見, 是否run得未夠, 還是要換線, 有什過好介紹, OASIS 6 1出2得唔得, OR SUB-3好D, 筆植唔多過年1,500, 還是要加百事ching薄餅, 禾的amp是906, 用完+仔eq auto cal完後, 再用sound meter將各聲壓set去75db, thx.

timmywan

未煲夠呀

Foverking

回復 2# timmywan


    CHING, +仔係唔係都要煲1兩百個鐘...

timmywan

回復  timmywan


    CHING, +仔係唔係都要煲1兩百個鐘...
Foverking 發表於 2011-5-2 22:10

    差不多

hifilau

Hi Ching,
How much!! please Pm me.Thanks

sk555

新入了1000ULTRA, 用緊條舊SUB-X比佢, 電源線用緊跟機的, RUN了2+幾個鐘, 覺得力度差D, D聲都係唔夠緊/快,  ...
Foverking 發表於 2011-5-2 21:33

    師兄，太夜睇到個post，有野幾樣野的，但太夜我遲些再傾，有d可以即做，係換條pc先，其他野唔好換住，你張sub volumn續點加大再聽下點，試左先，其他下步講

Foverking

回復 6# sk555


    嘩......c姐......唔係太夜.....係太早啦 , 多d休息啦啦! 我試過慢慢調大個vol, 但bass走唔到, 感覺耳鳴(唔書服), 試過將隻+仔轉角度, 好左d, 但未係好理想, 電源線有什麼好介紹, 但要平

bigpun1975

Aet hhs

sing1357

師兄試下reset 個 eq(唔用sub仔個eq，無mic情況下按remote個"eq"制兩秒)。我個case唔用sub仔eq好過用....

Foverking

回復 8# bigpun1975


    C兄, 此線幾多女一呎和鴨記有無得買

Foverking

回復 9# sing1357


    哦...即係將+仔變回原來設定? 都可以玩吓, 一試無房, thx

sing1357

回復  sing1357


    哦...即係將+仔變回原來設定? 都可以玩吓, 一試無房, thx
Foverking 發表於 2011-5-3 14:39

    試下lor，又唔駛錢

sk555

回復  sing1357


    哦...即係將+仔變回原來設定? 都可以玩吓, 一試無房, thx
Foverking 發表於 2011-5-3 14:39

    worth to try, i don't use it too

bigpun1975

回復 10# Foverking


    约150一呎，你可以打去高明問吓先

sk555

回復  sk555


    嘩......c姐......唔係太夜.....係太早啦 , 多d休息啦啦! 我試過慢慢調大個vo ...
Foverking 發表於 2011-5-3 13:44

我用古河pc咋，呢度好少ching用，我就用得幾滿意，無話肥呀緊呀，rca就用sub-3，出黎效果係有punch有墊底唔會乾有質感。
你個污化擺位點架。

randyma

回復 15# sk555
If I want the crossover of ultra is handle my amplier, Do I set the crossover of Ultra into direct. Please advice.

pam_jack

回復  sk555
If I want the crossover of ultra is handle my amplier, Do I set the crossover of Ultra  ...
randyma 發表於 2011-7-14 22:44

Yes!
See P. 10 for clear instruction...

http://www.velodyne.com/vproduct ... %20C_web.pdf?stdl=1

rklpoon

師兄試下reset 個 eq(唔用sub仔個eq，無mic情況下按remote個"eq"制兩秒)。我個case唔用sub仔eq好過用.... ...
sing1357 發表於 2011-5-3 13:54

    It seems to me that to reset the sub,you have to Pres 1,2,3,4,4,3,2,1 on the remote and then a code like p3(not sure of this) rerturns to confirm

pam_jack

It seems to me that to reset the sub,you have to Pres 1,2,3,4,4,3,2,1 on the remote and then  ...
rklpoon 發表於 2011-7-15 08:56

Yes!
Just pressing the EQ on remote without the mic will resume the last setting...

sk555

回復  sk555
If I want the crossover of ultra is handle my amplier, Do I set the crossover of Ultra  ...
randyma 發表於 2011-7-14 22:44

拎去direct