請教EM-U 1010 同軸及光縴輸出無聲

天下第一刀

請教EM-U 1010 同軸及光縴輸出無聲
剛訂購EM-U 1010 安裝後同軸及光縴輸出無聲﹐
１　在 Wave 1/2 加入電平表﹐顯示正常
２　在 Wave 1/2 加入 SEND to S/PDIF L/R PCI CARD
３　MAIN MIX　電平顯示正常

系統Windows 7 Professional　３２ＢＩＴ

伏喱哩

未裝好DRIVER

天下第一刀

未裝好DRIVER
伏喱哩 發表於 2011-7-13 16:35

Driver update都ＯＫ了，就是无声
重安装了几次也无声
ＷＩＮＤＯＷＳ　７　有很多麻烦

伏喱哩

ASIO係比USB

同軸及光纖要選翻SOUND CARD DRIVER OR DIRECT DOUND

howin

刀哥都有野要請教?

m40

Based on my previous experience on EMU, you need to “shift” the audio signal from default analog output (1/2) to spdif channels (3/4 or higher number, depends on your card model)

Use EMU’s native Asio driver (don’t confuse with Asio4all which you don't need), in your playback software e.g. foobar, you need to map the channel output to channel 3/4 (or higher, need testing) inside ASIO configuration.
If use JRiver, change channel offset from default 0 to something higher number (2, 4, 6, etc) until the audio channels is correctly “shifted” to spdif channel.   

Follow similar logic if use WASAPI.

Good luck.

天下第一刀

Based on my previous experience on EMU, you need to “shift” the audio signal from default analog o ...
m40 發表於 2011-7-14 12:12

Thanks for share your experience.

Now ,That EMU1010 is working , The problem is my display set to 150% that make me cannot to selete S/PDIF from I/O setting.

And it's easy to setup:
New Session>Selete 44.1KHZ or higher
> In I/O , Selete S/PDIF from Optical Output

Don,t need to SEND anything from all Trips

E-MU1010 is a professinal digital sound card , and the Jitter is very low

天下第一刀

刀哥都有野要請教?
howin 發表於 2011-7-14 11:35

可能眼“老化”﹐將顯示器ＳＥＴ到１５０％﹐旁邊的字延伸到選擇按鈕﹐使那個Ｓ
∕ＰＤＩＦ無法選擇﹐將顯示器ＳＥＴ到１００％　就ＯＫ了。
比較了ＣＤ機﹑ＨＤ　及電腦的幾種Ｓ∕ＰＤＩＦ輸出﹐個人聽感﹕
ＣＤ機Ｓ∕ＰＤＩＦ聲大一些﹐ＨＤ聲小一些並非常接近ＣＤ音質﹔電腦除ＨＤＭ
Ｉ用電視轉光縴的解析度高一點外﹐ＨＤＭＩ有嚴重的超高頻干擾引起互調失真
（裂高音）最好的電腦聲卡也有一點延時聲﹐看來ＨＩＦＩ還是﹕簡潔至上最ＨＩ
ＥＮＤ