First time with SolidSteel

SimpleLife

First box in 2013 and first time with SolidSteel.

SolidSteel H6

eddiey4k

Congrads! Any improvement?

SimpleLife

Just assembly. Not tested yet.

vincentfokhk

恭喜師兄

ke1

恭喜師兄

racewong

記得睇manuel, 留意每層果三粒[向上既圓釘]點樣set法.

fatso

SimpleLife 發表於 2013-2-24 23:48
Just assembly. Not tested yet.

唔駛試都知正啦

petkei

racewong 發表於 2013-2-25 10:07
記得睇manuel, 留意每層果三粒[向上既圓釘]點樣set法.

點解我上次開箱果時揾極都揾唔到嘅 都唔知有冇裝錯tim

racewong

petkei 發表於 2013-2-25 11:27
點解我上次開箱果時揾極都揾唔到嘅 都唔知有冇裝錯tim

簡單D講, 當你用鋁釘墊起塊板後, 再用六角匙慢慢扭幾粒[向上的圓釘], 直至[剛剛]接觸到塊板為止.

你果個H6三層共九粒圓釘. 你慢慢玩啦.

miumiu

請問樓主張相是否已經是完成品？(因好似沒有層板)

SimpleLife

未完成，後面個盒就係D板。因屋內仲有野攪，唔砌住。

petkei

racewong 發表於 2013-2-25 11:41
簡單D講, 當你用鋁釘墊起塊板後, 再用六角匙慢慢扭幾粒[向上的圓釘], 直至[剛剛]接觸到塊板為止.

你果個 ...

真係裝錯左tim,我以為果九粒圓釘係裝飾！

cth6996

petkei 發表於 2013-2-25 20:10
真係裝錯左tim,我以為果九粒圓釘係裝飾！

咩 model？

racewong

petkei 發表於 2013-2-25 20:10
真係裝錯左tim,我以為果九粒圓釘係裝飾！

好多人都似為係裝飾, 所以見有師兄出POST, 咪提一提佢囉.

jovi007

racewong 發表於 2013-2-25 21:40
好多人都似為係裝飾, 所以見有師兄出POST, 咪提一提佢囉.

我都係剛剛知，買回来時都吾覺manual有寫

eddiey4k

petkei 發表於 2013-2-25 20:10
真係裝錯左tim,我以為果九粒圓釘係裝飾！

果九粒圓釘應該有 damping 作用

SimpleLife

Steps to setup (extracted from internet):

I simply had to install the spike feet on the bottom of the frame, set the duraluminium cones in their sockets and position the shelves. I installed the three decoupling screws for each shelf by tightening them with the included wrench until they just touched the underside of the shelf. That was all there was to it. I placed my components on the shelves, recalibrated the decoupling screws as necessary, and I was ready to go.

curtis9797

racewong 發表於 2013-2-25 11:41
簡單D講, 當你用鋁釘墊起塊板後, 再用六角匙慢慢扭幾粒[向上的圓釘], 直至[剛剛]接觸到塊板為止.

你果個 ...

thanks 又學倒野

petkei

cth6996 發表於 2013-2-25 21:17
咩 model？

同樓主一樣H6

chakat

樓主，恭喜有好嘢！！！！可否PM在那裡買及幾錢呢？我都想今年初換Solidsteel！Thanks.